SWD.de/+ Manufacturer +/+ + Additional manufacturers + +/Corman Technologies Ltd./CorNet 10base Ethernet Cards products

COR-CT-E001 53,00 �

Thu, 04 Apr 2013 19:24:29 +0200

CorNet 10base Ethernet Boot ROM(CT-E101, E104), see also BET-E001

COR-CT-E002 52,00 �

Thu, 04 Apr 2013 19:24:29 +0200

CorNet 10base Ethernet Boot ROM(CT-E110)

COR-CT-E005 53,00 �

Thu, 04 Apr 2013 19:24:29 +0200

CorNet CT-E005 10base Ethernet Boot ROM(CT-E112)see also BET-E005

COR-CT-E101 59,00 �

Thu, 04 Apr 2013 19:24:29 +0200

CT-E050T/CT-E050C

CorNet Ethernet Multimode Media Converter

DESCRIPTION

The CT-E050T and the CT-E050C media converters change an Ethernet 10base-T copper wire based signal to a 10base-FL multimode fiber optic based signal. When used in a point-to-point full duplex connection, the converter extends the distance of Ethernet network links to a maximum of 2km using multimode fiber cable. Users can select from either ST or SC connectors.

OPERATING ENVIRONMENT

Power:	+12VDC @ 800mA min
Operating Temperature:	0�C to 40�C
Storage Temperature:	-40�C to 70�C
Operating Humidity:	10% to 90% (non-condensing)
Storage Humidity:	5% to 90% (non-condensing)

LAN INTERFACE

10Mbps transmission rate

10base-T: RJ-45 connector

10base-FL: ST or SC multimode connector

PHYSICAL SPECIFICATIONS

PCB mounted fiber optic ST or SC module
LED indicator for power
LED indicators for link
UTP:	indicates 10base-T link is established and activity on port
FX:	indicates 10base-FL link is established and activity on port
Dimensions:	101mm x 96mm x 25mm (WxDxH) 3.98� x 3.78� x 0.98�

WARRANTY

2 years

INSTALLATION CONSIDERATIONS

10 base-FL ETHERNET

Fiber Optic Cable

62.5/125µm 850nm multimode fiber optic cable is recommended
Dual ST or SC connectors
Distance from port to port: 2km (1.25 miles)

10 base-T ETHERNET

Twisted Pair Cable Type

Category 5 unshielded twisted pair
Distances From node to hub: 100m (325 ft)
RJ-45 connector

CONFORMS TO THE FOLLOWING STANDARDS

10base-T:	IEEE 802.3 10base-FL IEEE 802.3 10base-T
EMC:	EN 50081-1:1992
	EN55022:1998 EN61000-3-2:1995 EN61000-3-3:1995	CISPR 22:1997 IEC1000-3-2:1995 IEC1000-3-3:1994
	EN 50082-1:1997
	EN61000-4-2:1995 EN61000-4-3:1996 EN61000-4-4:1995	IEC 61000-4-2:1995 IEC 61000-4-3:1995 IEC 61000-4-4:1995
Products are marked as certified to the CE standards

COR-CT-E104 94,00 �

Thu, 04 Apr 2013 19:24:29 +0200

Corman CT-E104

CorNet 10base Ethernet Adapter ISA

This is a 16-bit Ethernet
NE2000 compatible Adapter for the
ISA bus. It supports jumperless configuration
with an easy to use configuration program. It also
supports Plug and Play configuration. It has jacks for
unshielded twisted pair or coax connections to the
network. The adapter is supplied with a QNX network
driver, along with drivers for most other popular
operating systems. A QNX network boot ROM is also
available.

LAN Interface

8/16 bit ISA bus
10Mbps transmission rate
NE2000 compatible
Full or half duplex auto negotiation
I/0 mapped (Can be set in the range from 200 to 3E0 in increments of 20)
Interrupts (2, 3, 4, 5, 10, 11, 12, 15)
ROM: Optional Boot ROM
RAM: 16KB packet buffer
Jumperless NE2000 configuration
Configuration via PnP BIOS or supplied QNX and DOS setup programs
Autodetect BNC or UTP interface
Uses NE2000 drivers or provided drivers for most popular networking operating systems

Operating Environment

Power:	+5V DC @ 0.5A max
Operating Temperature:	0 to 55�C
Storage Temperature:	-40�C to 70�C
Operating Humidity:	10% to 90% (non-condensing)
Storage Humidity:	5% to 90% (non-condensing)

Physical Specifications

PCB mounted low profile RJ-45 and BNC Connectors
LED indicator for link status: indicates link is operating normally
Dimensions: 157mm x 60mm (6.18� x 2.36�)

Warranty

2 years

Installation Considerations
ETHERNET

Twisted Pair Cable

Category 3 or better unshielded twisted pair
Distance from node to hub: 100m (325 ft)
Based on recommended maximum of 5 links and 4 repeaters between nodes.

Coax Cable

Thin coaxial cable: RG-58A/U 50 ohm coaxial cable (0.2 inch diameter)
Maximum Segment length: 185m (600 ft)
Minimum Segment length: 0.5m (1.6 ft)
Maximum number of coax segments between nodes: 5
Maximum number of nodes per coax segment: 30
BNC 50 ohm terminator required at each end of trunk and one must be grounded

Conforms to the Following Standards

Ethernet:

IEEE 802.3 10base-T and 10base-2

EMC:

EN55022:1998

EN61000-3-2:1995

EN61000-3-3:1995

EN50024:1998

CISPR 22:1997

Products are marked as certified to the CE standards.

ALSO AVAILABLE
CT-E001 QNX Boot ROM

COR-CT-E110 64,00 �

Thu, 04 Apr 2013 19:24:29 +0200

Corman CT-E104

CorNet 10base Ethernet Adapter ISA

LAN Interface

8/16 bit ISA bus
10Mbps transmission rate
NE2000 compatible
Full or half duplex auto negotiation
I/0 mapped (Can be set in the range from 200 to 3E0 in increments of 20)
Interrupts (2, 3, 4, 5, 10, 11, 12, 15)
ROM: Optional Boot ROM
RAM: 16KB packet buffer
Jumperless NE2000 configuration
Configuration via PnP BIOS or supplied QNX and DOS setup programs
Autodetect BNC or UTP interface
Uses NE2000 drivers or provided drivers for most popular networking operating systems

Operating Environment

Power:	+5V DC @ 0.5A max
Operating Temperature:	0 to 55�C
Storage Temperature:	-40�C to 70�C
Operating Humidity:	10% to 90% (non-condensing)
Storage Humidity:	5% to 90% (non-condensing)

Physical Specifications

PCB mounted low profile RJ-45 and BNC Connectors
LED indicator for link status: indicates link is operating normally
Dimensions: 157mm x 60mm (6.18� x 2.36�)

Warranty

2 years

Installation Considerations
ETHERNET

Twisted Pair Cable

Category 3 or better unshielded twisted pair
Distance from node to hub: 100m (325 ft)
Based on recommended maximum of 5 links and 4 repeaters between nodes.

Coax Cable

Thin coaxial cable: RG-58A/U 50 ohm coaxial cable (0.2 inch diameter)
Maximum Segment length: 185m (600 ft)
Minimum Segment length: 0.5m (1.6 ft)
Maximum number of coax segments between nodes: 5
Maximum number of nodes per coax segment: 30
BNC 50 ohm terminator required at each end of trunk and one must be grounded

Conforms to the Following Standards

Ethernet:

IEEE 802.3 10base-T and 10base-2

EMC:

EN55022:1998

EN61000-3-2:1995

EN61000-3-3:1995

EN50024:1998

CISPR 22:1997

Products are marked as certified to the CE standards.

ALSO AVAILABLE
CT-E001 QNX Boot ROM

COR-CT-E112(obsolet) 73,00 �

Mon, 15 Jul 2013 14:01:31 +0200

Corman CT-E112

CorNet 10base Ethernet Adapter PCI

This is a 32-bit Ethernet Adapter for the PCI
bus. It supports jumperless PCI Plug and Play
configuration. It has jacks for unshielded
twisted pair or coax connections to the network.
The adapter is supplied with a QNX network driver,
along with drivers for most other popular operating
systems. A QNX network boot ROM is also available.

LAN Interface

PCI bus (PCI specifications revision 2.1)
10Mbps transmission rate
NE2000 compatible
Full or half duplex auto negotiation
I/0 mapped (Set from PCI system BIOS)
Interrupts (Set from PCI system BIOS)
ROM: Optional Boot ROM
Jumperless configuration via PCI system BIOS
Autodetect BNC or UTP interface
Drivers for most popular networking operating systems

Operating Environment

Power:	+3.3VDC @ 758mA max
Operating Temperature:	0 to 55ºC
Storage Temperature:	-40ºC to 70ºC
Operating Humidity:	10% to 90% (non-condensing)
Storage Humidity:	5% to 90% (non-condensing)

Physical Specifications

PCB mounted low profile RJ-11 and BNC Connectors
LED indicator for link status
Dimensions: 120mm x 60mm (4.72” x 2.36”)

Warranty

2 years

Installation Considerations
ETHERNET

Twisted Pair Cable

Category 3 or better unshielded twisted pair
Distance from node to hub: 100m (325 ft)
Based on recommended maximum of 5 links and 4 repeaters between nodes.

Coax Cable

Thin coaxial cable: RG-58A/U 50 ohm coaxial cable (0.2 inch diameter)
Maximum Segment length: 185m (600 ft)
Minimum Segment length: 0.5m (1.6 ft)
Maximum number of coax segments between nodes: 5
5
Maximum number of nodes per coax segment: 30
BNC 50 ohm terminator required at each end of trunk and one must be grounded

Conforms to the Following Standards

Ethernet:

IEEE 802.3 10base-T and 10base-2

EMC:

EN55022:1994

EN61000-3-2:1995

EN61000-3-3:1995

EN50024:1998

CISPR 22

Products are marked as certified to the CE standards.

ALSO AVAILABLE
CT-E005 QNX Boot ROM