SWD.de/+ Manufacturer +/+ + Additional manufacturers + +/Corman Technologies Ltd./CorNet 10base Ethernet Hubs products

COR-CT-E205 111,00 �

Thu, 04 Apr 2013 19:24:29 +0200

Corman CT-E112

CorNet 10base Ethernet Adapter PCI

This is a 32-bit Ethernet Adapter for the PCI
bus. It supports jumperless PCI Plug and Play
configuration. It has jacks for unshielded
twisted pair or coax connections to the network.
The adapter is supplied with a QNX network driver,
along with drivers for most other popular operating
systems. A QNX network boot ROM is also available.

LAN Interface

PCI bus (PCI specifications revision 2.1)
10Mbps transmission rate
NE2000 compatible
Full or half duplex auto negotiation
I/0 mapped (Set from PCI system BIOS)
Interrupts (Set from PCI system BIOS)
ROM: Optional Boot ROM
Jumperless configuration via PCI system BIOS
Autodetect BNC or UTP interface
Drivers for most popular networking operating systems

Operating Environment

Power:	+3.3VDC @ 758mA max
Operating Temperature:	0 to 55�C
Storage Temperature:	-40�C to 70�C
Operating Humidity:	10% to 90% (non-condensing)
Storage Humidity:	5% to 90% (non-condensing)

Physical Specifications

PCB mounted low profile RJ-11 and BNC Connectors
LED indicator for link status
Dimensions: 120mm x 60mm (4.72� x 2.36�)

Warranty

2 years

Installation Considerations
ETHERNET

Twisted Pair Cable

Category 3 or better unshielded twisted pair
Distance from node to hub: 100m (325 ft)
Based on recommended maximum of 5 links and 4 repeaters between nodes.

Coax Cable

Thin coaxial cable: RG-58A/U 50 ohm coaxial cable (0.2 inch diameter)
Maximum Segment length: 185m (600 ft)
Minimum Segment length: 0.5m (1.6 ft)
Maximum number of coax segments between nodes: 5
Maximum number of nodes per coax segment: 30
BNC 50 ohm terminator required at each end of trunk and one must be grounded

Conforms to the Following Standards

Ethernet:

IEEE 802.3 10base-T and 10base-2

EMC:

EN55022:1994

EN61000-3-2:1995

EN61000-3-3:1995

EN50024:1998

CISPR 22

Products are marked as certified to the CE standards.

ALSO AVAILABLE
CT-E005 QNX Boot ROM

COR-CT-E210 187,00 �

Thu, 04 Apr 2013 19:24:29 +0200

Corman CT-E112

CorNet 10base Ethernet Adapter PCI

LAN Interface

PCI bus (PCI specifications revision 2.1)
10Mbps transmission rate
NE2000 compatible
Full or half duplex auto negotiation
I/0 mapped (Set from PCI system BIOS)
Interrupts (Set from PCI system BIOS)
ROM: Optional Boot ROM
Jumperless configuration via PCI system BIOS
Autodetect BNC or UTP interface
Drivers for most popular networking operating systems

Operating Environment

Power:	+3.3VDC @ 758mA max
Operating Temperature:	0 to 55�C
Storage Temperature:	-40�C to 70�C
Operating Humidity:	10% to 90% (non-condensing)
Storage Humidity:	5% to 90% (non-condensing)

Physical Specifications

PCB mounted low profile RJ-11 and BNC Connectors
LED indicator for link status
Dimensions: 120mm x 60mm (4.72� x 2.36�)

Warranty

2 years

Installation Considerations
ETHERNET

Twisted Pair Cable

Category 3 or better unshielded twisted pair
Distance from node to hub: 100m (325 ft)
Based on recommended maximum of 5 links and 4 repeaters between nodes.

Coax Cable

Thin coaxial cable: RG-58A/U 50 ohm coaxial cable (0.2 inch diameter)
Maximum Segment length: 185m (600 ft)
Minimum Segment length: 0.5m (1.6 ft)
Maximum number of coax segments between nodes: 5
Maximum number of nodes per coax segment: 30
BNC 50 ohm terminator required at each end of trunk and one must be grounded

Conforms to the Following Standards

Ethernet:

IEEE 802.3 10base-T and 10base-2

EMC:

EN55022:1994

EN61000-3-2:1995

EN61000-3-3:1995

EN50024:1998

CISPR 22

Products are marked as certified to the CE standards.

ALSO AVAILABLE
CT-E005 QNX Boot ROM

COR-CT-E211 197,00 �

Thu, 04 Apr 2013 19:24:29 +0200

CorNet 10base Ethernet-Hub 10-ports / european Modell(240V)