SWD.de/+ Manufacturer +/Hilscher GmbH/HIL-AS-Interface Hardware products

HIL-AIF104-ASI-15 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

AIF 104-ASI

Assembly Interface PC/104 AS-Interface interface The Assembly Interface carries out via a ribbon cable the signal of the post plug-in connector of the PC/104 card to a standardized connector at the housing. The variants are: the fielbus connection only, the diagnotic port only or both.

Product		AIF 104-ASI
Option		Cable length 5 cm \| -5 15 cm \| -15
Description		Assembly Interface PC/104 AS-Interface interface
Related products		CIF 104-ASI\P CIF 104-ASI\S CIF 104-ASI\H CIF 104-ASI\V


AS-Interface interface
Connector		2x COMBICON 2-pin
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		25 x 45 x 17 mm
Weight approx.		20 g
CE sign		Yes

HIL-AIF104-ASI-DIAG-15 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

AIF 104-ASI-DIAG-15-15

Product		AIF 104-ASI-DIAG
Option		Cable length 5 cm \| -5 15 cm \| -15
Description		Assembly Interface PC/104 AS-Interface- / Diagnostic interface
Related products		CIF 104-ASI\H CIF 104-ASI\V


AS-Interface interface
Connector		2x COMBICON 2-pin
Diagnostic Interface
Connector		DSub-male connector 9-pin
Display		RDY, RUN, CH1, CH2
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		25 x 89 x 20 mm
Weight approx.		60 g
CE sign		Yes

HIL-AIF104-ASI-DIAG-25 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

2701.632 Hilscher Verbindungs-Interface PC/104 AS-Interface/Diagnose 55cm Flachbandkabel

HIL-AIF104-DIAG-DC-15 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

AIF 104-DIAG-DC-15

Product		AIF 104-DIAG-DC
Option		Cable length 5 cm \| -5 15 cm \| -15
Description		Assembly Interface PC/104 Diagnostic interface
Related products		CIF 104-ASI\H CIF 104-ASI\V CIF 104-DNS\H CIF 104-DNS\V CIF 104-DNM\H CIF 104-DNM\V


Diagnostic Interface
Connector		DSub-male connector 9-pin
Display		RDY, RUN, CH1, CH2
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		25 x 45 x 17 mm
Weight approx.		20 g
CE sign		Yes

HIL-CIF104-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

CIF 104-ASIM

Communication Interface PC/104
AS-Interface-Master

Das Communication Interface als Master am AS-Interface-Netzwerk tauscht selbstständig die Daten zwischen den Busteilnehmern und einem internen Prozessabbild aus. Dieses wird im Dual-port memory geführt und steht somit der Applikation direkt zur Verfügung.
Die Konfiguration erfolgt über den Systemkonfigurator SyCon® oder direkt durch die Anwenderapplikation. Diese wird auf den Baugruppen gespeichert und steht beim Starten sofort zur Verfügung.

Fakten auf einen Blick

Ausführung des AS-Interface Protokollstacks ohne Belastung des PCs
Direkter Zugriff auf die Prozessdaten im Dual-Port-Memory
Einfache Funktionskontrolle über LED-Statusanzeige
Speichern der Konfigurationsdaten im internen FLASH
Grafischer Systemkonfigurator mit einheitlichem ‘look and feel’ für alle Feldbussysteme
Identische ‘easy to use’ Applikationsschnittstelle auf allen Communication Interfaces
Device-Treiber für Windows® und Linux werden mitgeliefert
OPC-Server lieferbar

Product		CIF 104-ASIM
Description		Communication Interface PC/104 AS-Interface-Master
Option		Connector 2x COMBICON 2-pin Square post 10-pin angled \| \P Square post 10-pin straight \| \S Square post 16-pin angled \| \H Square post 16-pin straight \| \V
In scope of delivery		C functions library DRV-TKIT COM interface DRV-COM Device driver Windows DRV-WIN Device driver Linux DRV-LNX Documentation on CD CD-SYS Basic version System Configurator
Order seperately		System Configurator SYCON-ASI
Related products		Device driver Windows CE DRV-CE SoftPLC-Kit OPC-Server SRV-OPC Service cable CAB-SRV
only for option \P \S		Flat ribbon cable CAB-PM Assembly Interf. AIF 104-ASI
only for option \H \V		Assembly Interf. AIF 104-ASI-DIAG Assembly Interf. AIF 104-ASI Assembly Interf. AIF 104-DIAG-DC


Card format		PC/104
Bus interface		ISA
Dual-Port-Memory		2 KByte
Interrupt		3-7, 9-12, 14, 15
AS-Interface interface		IEC 364-4-41
Transmission rate		167 kBaud
Controller		IX1
Interface		optically isolated
Connector		2x COMBICON 2-pin Square post 10-pin angled \P \H Square post 10-pin straight \S \V
Diagnostic Interface		RS232C, non-isolated
Connector		DSub-male connector 9-pin Square post 10-pin angled \P Square post 10-pin straight \S Square post 16-pin angled \H Square post 16-pin straight \V
Display		RDY, RUN, CH1, CH2
Operating voltage		5 V ±5% / 550 mA
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		90 x 96 x 25 mm
Weight approx.		120 g
CE sign		Yes

HIL-CIF104-ASM/H 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

CIF 104-ASIM

Communication Interface PC/104
AS-Interface-Master

The Communication Interface as a Master on the AS-Interface network exchanges independently the data between the devices on the bus and the internal process image. The process image is held in the dual-port memory and the application can access the data directly.
The configuration is carried out with the aid of our System Configurator SyCon® or directly from the application program. It is stored in the device and is available immediately at the start time.

Facts at a glance:

Execution of the AS-Interface protocol stack without load of the PC
Direct access to the process data in the Dual-Port-Memory
Easy diagnostic via LED status display
Configuration data is stored in internal FLASH memory
Graphic System Configurator with unified 'look and feel' for all fieldbus systems
Identical 'easy-to-use' application interface on all Communication Interfaces
Device driver for Windows® and Linux included
OPC server available

Product		CIF 104-ASIM
Description		Communication Interface PC/104 AS-Interface-Master
Option		Connector 2x COMBICON 2-pin Square post 10-pin angled \| \P Square post 10-pin straight \| \S Square post 16-pin angled \| \H Square post 16-pin straight \| \V
In scope of delivery		C functions library DRV-TKIT COM interface DRV-COM Device driver Windows DRV-WIN Device driver Linux DRV-LNX Documentation on CD CD-SYS Basic version System Configurator
Order seperately		System Configurator SYCON-ASI
Related products		Device driver Windows CE DRV-CE SoftPLC-Kit OPC-Server SRV-OPC Service cable CAB-SRV
only for option \P \S		Flat ribbon cable CAB-PM Assembly Interf. AIF 104-ASI
only for option \H \V		Assembly Interf. AIF 104-ASI-DIAG Assembly Interf. AIF 104-ASI Assembly Interf. AIF 104-DIAG-DC


Card format		PC/104
Bus interface		ISA
Dual-Port-Memory		2 KByte
Interrupt		3-7, 9-12, 14, 15
AS-Interface interface		IEC 364-4-41
Transmission rate		167 kBaud
Controller		IX1
Interface		optically isolated
Connector		2x COMBICON 2-pin Square post 10-pin angled \P \H Square post 10-pin straight \S \V
Diagnostic Interface		RS232C, non-isolated
Connector		DSub-male connector 9-pin Square post 10-pin angled \P Square post 10-pin straight \S Square post 16-pin angled \H Square post 16-pin straight \V
Display		RDY, RUN, CH1, CH2
Operating voltage		5 V ±5% / 550 mA
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		90 x 96 x 25 mm
Weight approx.		120 g
CE sign		Yes

HIL-CIF104-ASM/P 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

CIF 104-ASIM

Facts at a glance:

Execution of the AS-Interface protocol stack without load of the PC
Direct access to the process data in the Dual-Port-Memory
Easy diagnostic via LED status display
Configuration data is stored in internal FLASH memory
Graphic System Configurator with unified 'look and feel' for all fieldbus systems
Identical 'easy-to-use' application interface on all Communication Interfaces
Device driver for Windows® and Linux included
OPC server available

Product		CIF 104-ASIM
Description		Communication Interface PC/104 AS-Interface-Master
Option		Connector 2x COMBICON 2-pin Square post 10-pin angled \| \P Square post 10-pin straight \| \S Square post 16-pin angled \| \H Square post 16-pin straight \| \V
In scope of delivery		C functions library DRV-TKIT COM interface DRV-COM Device driver Windows DRV-WIN Device driver Linux DRV-LNX Documentation on CD CD-SYS Basic version System Configurator
Order seperately		System Configurator SYCON-ASI
Related products		Device driver Windows CE DRV-CE SoftPLC-Kit OPC-Server SRV-OPC Service cable CAB-SRV
only for option \P \S		Flat ribbon cable CAB-PM Assembly Interf. AIF 104-ASI
only for option \H \V		Assembly Interf. AIF 104-ASI-DIAG Assembly Interf. AIF 104-ASI Assembly Interf. AIF 104-DIAG-DC


Card format		PC/104
Bus interface		ISA
Dual-Port-Memory		2 KByte
Interrupt		3-7, 9-12, 14, 15
AS-Interface interface		IEC 364-4-41
Transmission rate		167 kBaud
Controller		IX1
Interface		optically isolated
Connector		2x COMBICON 2-pin Square post 10-pin angled \P \H Square post 10-pin straight \S \V
Diagnostic Interface		RS232C, non-isolated
Connector		DSub-male connector 9-pin Square post 10-pin angled \P Square post 10-pin straight \S Square post 16-pin angled \H Square post 16-pin straight \V
Display		RDY, RUN, CH1, CH2
Operating voltage		5 V ±5% / 550 mA
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		90 x 96 x 25 mm
Weight approx.		120 g
CE sign		Yes

HIL-CIF104-ASM/S 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

CIF 104-ASIM

Facts at a glance:

Execution of the AS-Interface protocol stack without load of the PC
Direct access to the process data in the Dual-Port-Memory
Easy diagnostic via LED status display
Configuration data is stored in internal FLASH memory
Graphic System Configurator with unified 'look and feel' for all fieldbus systems
Identical 'easy-to-use' application interface on all Communication Interfaces
Device driver for Windows® and Linux included
OPC server available

Product		CIF 104-ASIM
Description		Communication Interface PC/104 AS-Interface-Master
Option		Connector 2x COMBICON 2-pin Square post 10-pin angled \| \P Square post 10-pin straight \| \S Square post 16-pin angled \| \H Square post 16-pin straight \| \V
In scope of delivery		C functions library DRV-TKIT COM interface DRV-COM Device driver Windows DRV-WIN Device driver Linux DRV-LNX Documentation on CD CD-SYS Basic version System Configurator
Order seperately		System Configurator SYCON-ASI
Related products		Device driver Windows CE DRV-CE SoftPLC-Kit OPC-Server SRV-OPC Service cable CAB-SRV
only for option \P \S		Flat ribbon cable CAB-PM Assembly Interf. AIF 104-ASI
only for option \H \V		Assembly Interf. AIF 104-ASI-DIAG Assembly Interf. AIF 104-ASI Assembly Interf. AIF 104-DIAG-DC


Card format		PC/104
Bus interface		ISA
Dual-Port-Memory		2 KByte
Interrupt		3-7, 9-12, 14, 15
AS-Interface interface		IEC 364-4-41
Transmission rate		167 kBaud
Controller		IX1
Interface		optically isolated
Connector		2x COMBICON 2-pin Square post 10-pin angled \P \H Square post 10-pin straight \S \V
Diagnostic Interface		RS232C, non-isolated
Connector		DSub-male connector 9-pin Square post 10-pin angled \P Square post 10-pin straight \S Square post 16-pin angled \H Square post 16-pin straight \V
Display		RDY, RUN, CH1, CH2
Operating voltage		5 V ±5% / 550 mA
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		90 x 96 x 25 mm
Weight approx.		120 g
CE sign		Yes

HIL-CIF104-ASM/V 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

CIF 104-ASIM

Facts at a glance:

Execution of the AS-Interface protocol stack without load of the PC
Direct access to the process data in the Dual-Port-Memory
Easy diagnostic via LED status display
Configuration data is stored in internal FLASH memory
Graphic System Configurator with unified 'look and feel' for all fieldbus systems
Identical 'easy-to-use' application interface on all Communication Interfaces
Device driver for Windows® and Linux included
OPC server available

Product		CIF 104-ASIM
Description		Communication Interface PC/104 AS-Interface-Master
Option		Connector 2x COMBICON 2-pin Square post 10-pin angled \| \P Square post 10-pin straight \| \S Square post 16-pin angled \| \H Square post 16-pin straight \| \V
In scope of delivery		C functions library DRV-TKIT COM interface DRV-COM Device driver Windows DRV-WIN Device driver Linux DRV-LNX Documentation on CD CD-SYS Basic version System Configurator
Order seperately		System Configurator SYCON-ASI
Related products		Device driver Windows CE DRV-CE SoftPLC-Kit OPC-Server SRV-OPC Service cable CAB-SRV
only for option \P \S		Flat ribbon cable CAB-PM Assembly Interf. AIF 104-ASI
only for option \H \V		Assembly Interf. AIF 104-ASI-DIAG Assembly Interf. AIF 104-ASI Assembly Interf. AIF 104-DIAG-DC


Card format		PC/104
Bus interface		ISA
Dual-Port-Memory		2 KByte
Interrupt		3-7, 9-12, 14, 15
AS-Interface interface		IEC 364-4-41
Transmission rate		167 kBaud
Controller		IX1
Interface		optically isolated
Connector		2x COMBICON 2-pin Square post 10-pin angled \P \H Square post 10-pin straight \S \V
Diagnostic Interface		RS232C, non-isolated
Connector		DSub-male connector 9-pin Square post 10-pin angled \P Square post 10-pin straight \S Square post 16-pin angled \H Square post 16-pin straight \V
Display		RDY, RUN, CH1, CH2
Operating voltage		5 V ±5% / 550 mA
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		90 x 96 x 25 mm
Weight approx.		120 g
CE sign		Yes

HIL-CIF30-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

CIF 30-ASIM

Communication Interface ISA AS-Interface-Master

AS-Interface-Master

Das Communication Interface als Master am AS-Interface-Netzwerk tauscht selbstständig die Daten zwischen den Busteilnehmern und einem internen Prozessabbild aus. Dieses wird im Dual-port memory geführt und steht somit der Applikation direkt zur Verfügung. Die Konfiguration erfolgt über den Systemkonfigurator SyCon® oder direkt durch die Anwenderapplikation. Diese wird auf den Baugruppen gespeichert und steht beim Starten sofort zur Verfügung.



Fakten
Ausführung des AS-Interface- Protokollstacks ohne Belastung des PCs
Direkter Zugriff auf die Prozessdaten im Dual-port memory
Einfache Funktionskontrolle über LED-Statusanzeigen
Speichern der Konfigurationsdaten im internen FLASH
Grafischer Systemkonfigurator mit einheitlichem ‘look and feel’ für alle Feldbussysteme
Identische ‘easy to use’ Applikationsschnittstelle auf allen Communication Interface
Device-Treiber für Windows® und Linux werden mitgeliefert
OPC-Server lieferbar

Produkte	CIF 30-ASIM
Beschreibung	Communication Interface ISA
Beschreibung	AS-Interface-Master
Im Lieferumfang enthalten	C functions library DRV-TKIT
	COM interface DRV-COM
	Device Treiber Windows DRV-WIN
	Device Treiber
	Dokumentation auf CD CD-SYS
	Basisversion Systemkonfigurator
Seperat zu bestellen	System Configurator SYCON-ASI
Zugehörige Produkte	Device driver Windows CE DRV-CE
	SoftPLC-Kit
	OPC-Server SRV-OPC
	Servicekabel CAB-SRV
Kartenformat	PC
Bus Interface	ISA
Dual-port memory	2 KByte
Interrupt	3-7, 9-12, 14, 15
AS-Interface-Schnittstelle	IEC 364-4-41
Übertragungsrate	167 kBaud
Controller	IX1
Schnittstelle	potentialfrei
Steckverbinder	2x COMBICON 2-polig
Diagnose Schnittstelle	RS232C, potentialgebunden
Steckverbinder	DSub-Stecker 9-polig
Anzeige	RDY, RUN, CH1, CH2
Betriebsspannung	5 V +5% / 550 mA
	+12 V +5% / 50 mA
	-12 V +5% / 50 mA
Betriebstemperatur	0 °C - 55 °C
Maße	134 x 107 x 20 mm
Gewicht	150 g
CE Zeichen	Ja

HIL-CIF50-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

CIF 50-ASIM

Communication Interface PCI
AS-Interface-Master

With the cifX communication interface, the user will have a unified standard for all Real-Time Ethernet and Fieldbus systems on different hardware platforms.
The complete protocol stack will be exectued on the PC card and data exchange to the host will be done via Dual-Port-Memory or DMA. Hilscher offers the cifX PC communication cards with PCI, PCI Express, Mini PCI, Mini PCI Express, PCI-104, PC/104, Compact PCI and Low Profile PCI Express interface. With a rotary switch an easy and reliable slot assignemt can be done for the PCI and PCI Express types.

A complete software package including a single FDT/DTM based configuration tool for all products and networks, documentation, loadable firmware and driver tool-kit is always in the scope of delivery.

Due to the own network controller netX a 10-years delivery is guaranteed.

Facts at a glance:

Execution of the AS-Interface protocol stack without load of the PC
Direct access to the process data in the Dual-Port-Memory
Easy diagnostic via LED status display
Configuration data is stored in internal FLASH memory
Graphic System Configurator with unified 'look and feel' for all fieldbus systems
Identical 'easy-to-use' application interface on all Communication Interfaces
Device driver for Windows® and Linux included
OPC server available

Product		CIF 50-ASIM
Description		Communication Interface PCI AS-Interface-Master
In scope of delivery		C functions library DRV-TKIT COM interface DRV-COM Device driver Windows DRV-WIN Device driver Linux DRV-LNX Documentation on CD CD-SYS Basic version System Configurator
Order seperately		System Configurator SYCON-ASI
Related products		SoftPLC-Kit OPC-Server SRV-OPC Service cable CAB-SRV


Card format		PC
Bus interface		PCI
Dual-Port-Memory		2 KByte
Interrupt		3-7, 9-12, 14, 15 via plug and play
AS-Interface interface		IEC 364-4-41
Transmission rate		167 kBaud
Controller		IX1
Interface		optically isolated
Connector		2x COMBICON 2-pin
Diagnostic Interface		RS232C, non-isolated
Connector		DSub-male connector 9-pin
Display		RDY, RUN, CH1, CH2
Operating voltage		5 V ±5% / 550 mA +12 V ±5% / 50 mA -12 V ±5% / 50 mA
Operating temperature		0 °C - 55 °C
Dimensions (LxWxH)		134 x 107 x 20 mm
Weight approx.		150 g
CE sign		Yes

HIL-COM-AS-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

1523.630 Hilscher Communication Module COM-AS-ASM AS-Typ AS-Interface-Master Combicon

HIL-COM-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

1500.630 Hilscher Communication Module COM-ASM AS-Interface-Master

HIL-COM-BA-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

1522.630 Hilscher Communication Module COM-BA-ASM BA-Typ AS-Interface-Master Combicon

HIL-COM-BN-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

1522.631 Hilscher Communication Module COM-BN-ASM BN-Typ AS-Interface-Master Pfosten 30-pol. gerade

HIL-COM-CA-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

1521.630 Hilscher Communication Module CA-Typ AS-Interface-Master Combicon

HIL-COM-CN-ASM 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

1521.631 Hilscher Communication Module CN-Typ AS-Interface-Master Pfostenverbinder 30-polig gerade

HIL-NETX100 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

NETX 100

netX 100 Network Controller

The netX is a highly integrated network controller with a new system architecture optimized for communication and maximum data throughput.

Based on the 32-Bit CPU ARM 926EJ-S cycled at 200 MHz, it possesses a memory management unit, caches, DSP and Java extensions. The internal memory of 144 KByte RAM and 32 KByte ROM that contains the Bootloader is sufficient for smaller applications whereas for Windows CE and Linux it is supplemented with the 32 Bit Memory Controller memory externally with SDRAM, SRAM or FLASH. The connection to a primary Host is carried out via the Dual-portmemory interface, which is configurable for stand-alone applications also as a 16 Bit extension bus. Comprehensive peripheral functions, serial interfaces such as UART, USB, SPI, I²C as well as the integrated graphic controller permit a wide spectrum of applications. Yet, it is the central data switch and the four freely configurable communication channels with their own intelligence that is the main characteristic of the netX as a "high end” network controller.

The data switch connects via five data paths to the ARM CPU and the communication, graphic and Host controllers with the memory or the peripheral units. In this way the controllers transmit their data in parallel, contrary to the traditional sequential architecture with only one common data bus and additional bus allocation cycles.

The controllers of the four communication channels are structured on two levels and are identical to each other. They consist of dedicated ALUs and special logic units that receive their protocol functions via Microcode. Two channels posses an additional integrated PHY for Ethernet. The Medium-Access-Controller xMAC sends or receives the data according to the respective bus access process and encrypts or converts these into Byte depictions. The Protocol Execution Controller xPEC compiles these into data packets and controls the telegram traffic. These are exchanged in DMA blocks over the memory of the ARM. In addition, every channel has a Dual-port-memory available for status information or as local data picture.

With the intelligent communication ALUs, the netX carries out the most varied protocols and protocol combinations and can synchronize them independently of the reaction time of the CPU – an absolutely new feature in industrial communication technology.

Facts at a glance:

Flexible “high end” network controller or highly integrated single chip solution for applications and communication
Four communication channels as Real-Time-Ethernet or fieldbus interface´s (individually configurable)
New system architecture optimized for communication and high data throughput
32-Bit/200MHz CPU ARM 926 with 200 MIPs computing power for Windows CE and Linux
Dual-Port-Memory, AD converter and graphic controller on chip

Product		NETX 100
Description		netX 100 Network Controller


Computer Core
Processor		ARM 926EJ-S, 200 MIPS, ARMv5TE-command set with DSP- and Java-extension
Cache		16 KByte commands / 8 KByte Data
Tightly Coupled Memory		8 KByte Data
Memory Managment Unit		Windows CE- and Linux-Support
Internal memory
RAM		144 KByte, of this 16 KByte with external voltage supply
ROM		32 KByte with Bootloader and Real-Time-Kernel
Ethernet interface
Ports		2 x 10BASE-T/100BASE-TX, Half-/Full-Duplex, IEEE 1588 time stamp
PHY		Integrated, Auto-Negotiation, Auto-Crossover
Real-Time-Ethernet		EtherCAT with three FMMUs and four Sync-Manager Ethernet/IP Powerlink with integrated Hub PROFINET RT with integrated Switch SERCOS-III Modbus IDA
Fieldbus-Interface
Channels		In case Ethernet isn't used two addictional fieldbus interfaces are available. Theses system can be combined arbitrarily.
Systems		AS-Interface, Master only CANopen / DeviceNet PROFIBUS, Master and Slave CC-Link, Slave only
Peripherals
IEEE 1588 System Time		32-bit second counter, 32-bit nanosecond counter
USB		Revision 1.1, 12 MBaud Full-Speed, Host- or Device-Mode
UART		16550 compatible, max. 3 MBaud, RTS/CTS support Quantity 3
I²C		Master and Slave mode, 50 KHz up to 3.4 MHz, 16-bit FIFO, Quantity 2
SPI		Master- and Slave-Mode, max. 10 MHz, 3 Chip-Select-Signals
AD-Converter		2 x 4 Channels with 1MS/s Sample&Hold and 10 Bit-resolution Single ended, Common Analog Ground, external reference voltage
PWM		0–20 kHz/12 Bit-resolution 0–80 kHz/10 Bit-resolution
Encoder		2 Channels, Impuls quadruplication, digital input filter
General I/Os		3.3 V / 6 mA, Quantity 16
Status LEDs		2 LEDs dual colored, 3.3 V/9 mA, Quantity 2
Memory-Interface
Memory bus		32 Bit-Databus/24 Bit-Address bus
Address region		256 MByte SDRAM/64 MByte FLASH
Memory modules		SDRAM, SRAM, FLASH
Host-Interface
Dual-Port-Memory Mode		8/16 Bit-Databus, 64 KByte configurable in 8 Blocks, emulated by internal RAM
Extension-Mode		8/16 Bit-Databus, 24 Bit-Address bus, Bustiming adjust table
PIO-Mode		Freely programmable Inputs and Outputs
Debug-Interface
JTAG		ARM-Processor and Boundary-Scan
ETM		Embedded Trace Macrocell, ETM9 V2 Medium Size
Operating Requirements / Housing / Miscellaneous
System cycles		200 MHz ARM / 100 MHz Periphery
Signal level		3.3 V
Power supply		1.5 V for the core 3.3 V for Input/Output
Operating temperature		without heat sink –40..+70 °C with heat sink 10°/W –40..+85 °C
Storage temperature		-65°C..+150°C
Power consumption		PHYs switched off typ. 1.0 W PHYs switched on typ. 1.5 W
Housing		PBGA, 1 mm raster, 345 Pins Dimensions 22 x 22 mm

HIL-NETX100(BOX) 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

2220.100 AS-Interface ASICs netX100 Netwerk Controller STEP A 15 Stck

HIL-NETX100(PACKAGE) 0,00 �

Sun, 20 Jan 2019 14:35:24 +0100

2220.300 AS-Interface ASICs netX100 Network Controller STEP A 300 Stck